Spray drying granulator is a new type of proprietary Chinese medicine and granulator for western medicine, which combines spray drying technology with fluidized bed granulation technology. The equipment is integrated with mixing, spray drying, granulating and granular coating. It can produce the products of Chinese patent medicine with small dosage, low dose, sugar free or low sugar. It is easy to dissolve and disintegrate easily, and the tablet is easy to disintegrate. It meets the "GMP" requirement.
In the aspects of granulating speed, particle quality and automation level, it has made an important step towards the international advanced level. Main uses food industry: granulated sugar, cocoa, coffee, spice, milk powder, condiment and so on. Pharmaceutical industry: Chinese medicine extract, tablet granule, capsule granule, low sugar or sugar free proprietary Chinese medicine granule. Other industries: pesticides, feedstuffs, fertilizers, pigments, dyestuffs, etc.
将干燥主机就位，然而连接主机与加热单元的管道。将加热器就位； 按设备布置图将旋风分离器、布袋除尘器吊置厂房预先设定好的位置，先连接干燥主机与旋风分离器间的管道，然后连接旋风分离器与布袋除尘器间的管道 分别连接热风炉与鼓风机以及空气过滤器间的管道。同时连接布袋除尘器与引风机间的管道； 校正干燥主机与地平面的垂直度，干燥主机塔顶与地面垂直度应不大于10mm； 加料器就位，并与干燥主机连接； 各管道连接时，应嵌石棉绳或密封条(需达到GMP要求的需要硅橡胶密封垫)；固定各连接处的紧固件，以紧固件板紧无松动为止； 连接电柜线路，电柜应牢固接地，并注有明确标志(电线应穿管或走线盒) 干燥室、收集瓶采用透明钢化玻璃，确保喷雾过程看得见无污染，以便及时调整，空压机采用无油烟静音系列，＜60分贝 符合国家标准，316L不锈钢二流体喷嘴使雾化均一，颗粒均匀。
Place the drying main engine in place, but connect the pipe between the main engine and the heating unit. The heater is in place, the cyclone separator and the bag dust collector are suspended in advance by the equipment layout, and the pipe between the dryer and the cyclone separator is first connected. Then the pipe between the cyclone separator and the bag dust collector is connected to the pipes between the hot air stove and the air filter and the air filter respectively. At the same time, the pipe between the bag dust collector and the fan is connected; the verticality of the dry main engine and the ground plane should be corrected, the vertical degree of the top and ground of the dry host tower and the ground should not be more than 10mm; the feeder is in place and connected with the drying host; the asbestos rope or sealing strip should be embedded when the pipes are connected. The silicone rubber seal needs to be required to meet the requirements of the GMP. Fixing the fasteners in each connection to tighten the fastener plate and not be loose; connect the electric cabinet line, the electric cabinet should be firmly connected to the ground, and note the clear sign (the wire should be wearing tube or the line box), the drying room and the collection bottle are transparent toughened glass to ensure that the spray process can be seen without pollution, so that the air compressor can be adjusted in time and the air compressor is used no time. Lampblack mute series, < 60 dB is in line with national standard. 316L stainless steel two fluid nozzles make atomization uniform and particle even.
PID temperature control makes temperature control more accurate. Frequency jet can be automatically dredged to ensure continuity of spray process.